White Ensign ...

Discussions relating to the day-to-day running of Light Coastal Forces; shore establishments and mobile bases; command structure; strategy and tactics; training and logistics etc
half12
Seaman
Posts: 13
Joined: Mon Aug 08, 2016 3:34 pm

White Ensign ...

Postby half12 » Mon Aug 29, 2016 9:26 pm

Hello,

Could you please tell me what size was the White Ensign used on MTBs and MGBs ?

Best regards .. Herve

half12
Seaman
Posts: 13
Joined: Mon Aug 08, 2016 3:34 pm

Re: White Ensign ...

Postby half12 » Mon Sep 12, 2016 2:49 pm

Hello,

... No idea about the White Ensign size ??

Best regards .. Herve

Admin
Site Admin
Posts: 500
Joined: Thu Jul 02, 2009 7:40 pm

Re: White Ensign ...

Postby Admin » Wed Sep 14, 2016 2:48 am

The 1937 edition of Manual of Seamanship cites the following:
Measurement of Ensigns, Standards, etc.
The size of British Ensigns, Standards, and Union Flags is commonly expressed in terms of ‘breadths.’ This measurement, which is 9 inches, is used for describing the size of any of the above flags. Bunting is supplied in two widths broad 19 inches, and narrow, 9 inches.

In the Union Flags, Standards, and the White, Blue, and Red Ensigns the length is twice the breadth. In the Admirals’ Flags the length is 1 times the breadth.

When the size of one of the above flags is spoken of as say, “16 breadths,” it denotes that it is 16 x 9 inches (or 12 feet) broad and, as it is twice as long as it is broad, 24 feet long, except an Admiral’s Flag which would be 18 feet.

Each cloth of bunting has a few thicker threads worked not only into its edges, but also at every 6 inches of its warp, and this mark shows the bunting to be of Government make.
This is the mast ensign from MTB 632
mtb-632-ensign.jpg

half12
Seaman
Posts: 13
Joined: Mon Aug 08, 2016 3:34 pm

Re: White Ensign ...

Postby half12 » Thu Sep 15, 2016 5:49 pm

Hello,

Many thanks for this wonderful ensign from MTB 632 ...

... but the "1937 edition of Manual of Seamanship" is not compatible with my french brain ...
I will have read it again slowly to undertand ...!

Best regards .. Herve

Admin
Site Admin
Posts: 500
Joined: Thu Jul 02, 2009 7:40 pm

Re: White Ensign ...

Postby Admin » Thu Sep 15, 2016 6:25 pm

Hello Herve

I think the simple version of it is:

Ensigns always measure multiples of 9 inches (22.86cms), known as a 'breadth', so are either 9" (1 breadth), 18" (two breadths), 27" (three breadths) etc, and are also twice as long as they are wide, giving you 9" x 18" (22.86cm x 45.72cm), 18" x 36" or 27" x 54" etc. So that should make MTB 632's ensign measure one breadth at 9" x 18" originally before being worn down.

half12
Seaman
Posts: 13
Joined: Mon Aug 08, 2016 3:34 pm

Re: White Ensign ...

Postby half12 » Tue Sep 20, 2016 6:31 pm

Hello,

After some research, most of identified ensigns attributed to MTB/MGBs I have found have a 3 breadths width ...

and here is the answer from the Royal Navy National Museum : "... Only the Royal Navy still measure flags in breadths. 3 breadths is, I believe, the smallest flag manufactured, which is one and a half yard x three quarters. This would have been the correct flag size for a smaller vessel such as an MGB..."

... but as far as I remember, I have already seen a smaller Ensign ... need to search again !

Best regards .. Herve

Admin
Site Admin
Posts: 500
Joined: Thu Jul 02, 2009 7:40 pm

Re: White Ensign ...

Postby Admin » Wed Sep 21, 2016 2:28 am

It's hard to tell if the ensigns referred to are those intended for display on a flagstaff at the stern of a vessel, as set against one flown from the masthead like a signal flag. Judging by the string and the size of the flag's eyelets in the photo above, and the fact it was copied in a scanner, I would say it is more likely 9" in height than 27".


Return to “General Organisation”

Who is online

Users browsing this forum: No registered users and 1 guest